Metal roof leak repair for factories
TECO MSC fixes leaks, replaces roof sheets, repairs gutters and applies heat-reflective coating on metal roofs of factories, warehouses and service workshops while production continues below. The whole roof is surveyed first and quantities are agreed with the owner before work starts.
Buildings we serve: factories, plants, warehouses, car service workshops and pre-engineered steel buildings in Ho Chi Minh City and southern Vietnam.
Why patching under the drip does not work
Water on a metal roof runs along the corrugations and purlins. The drip point below is often several metres from the real opening, so patching where water falls brings the leak back next rainy season. The main sources are usually:
- Roofing screws: rusted or loose screws, hardened or missing rubber washers.
- Side laps and ridge caps: laps open at the rib ends, especially near the ridge.
- Roof fan bases and skylights: open edges let water run in along the ribs.
- Gutters: leaking joints, rusted-through sections, blocked downpipes that overflow inside.
- Corroded sheets: holes that cannot be patched and must be replaced.
Metal roof leak repair
- Remove rusted and loose screws, fit new screws with rubber washers.
- Clean and seal side laps and ridge caps with waterproofing tape.
- Rebuild the junctions at roof fan bases and ventilation skylights.
- Water-test after repair.
Roof sheet replacement and gutter repair
- Roof sheet replacement: remove corroded, holed sheets and fit new sheets of the same profile; check purlins and keep sound sections.
- Gutters: clean, seal leaking joints, replace rusted-through sections, clear downpipes.
Heat-reflective coating for metal roofs
White heat-reflective coating reflects most solar radiation and reduces heat passing through the sheets into the work area. How long the coating lasts depends mostly on surface preparation.
- Remove heavy rust with wire brushes and grinders; clean dust, moss and grease from the whole roof; let it dry fully.
- Spot-prime rust points, screw heads and joints, then apply anti-rust primer over the whole roof.
- Apply two coats of heat-reflective paint, the second at right angles to the first for even coverage.
No painting on damp sheets, in rain or in the midday heat.
Working safely while the factory runs
- Register the work and follow the factory or industrial park work-at-height permit.
- Lifelines along the roof; everyone on the roof wears a helmet and full-body harness clipped on at all times.
- Walk only along purlin lines; use a boom lift at hard-to-reach roof edges.
- Cordon off and cover the area below against rust dust and paint drips.
- Work zone by zone; no roof access in rain, strong wind or on wet sheets.
Completed projects
- Factory metal roof leak repair, 1,800 m², VSIP 1, Thuan An – new screws, sealed laps, fan bases treated, corroded sheets replaced, water-tested; production continued.
- Heat-reflective metal roof coating, 1,200 m², 2S Sai Gon Moi workshop – rust treatment, full primer, two heat-reflective coats; workshop kept running.
Frequently asked questions
Does production have to stop?
No. Both projects above were done while the workshops kept running, zone by zone with the area below covered.
Repair the leaks or replace the roof?
If the sheets are still thick enough and only screws and laps have failed, repair them. If corrosion and holes are widespread, replace the sheets. TECO MSC surveys the whole roof, recommends and agrees quantities before starting.
How much cooler does heat-reflective coating make it?
It depends on the coating type, colour and roof condition. TECO MSC advises on the coating based on the manufacturer’s data during the survey.
What about leaking concrete flat roofs?
Request a survey and quotation
TECO MSC surveys the whole roof and quotes leak repair, roof sheet replacement and heat-reflective coating in Ho Chi Minh City and southern Vietnam. Hotline: +84 911 111 929 · Send a survey request
Related services: Waterproofing and leak repair · 24/7 Emergency Repair · Periodic maintenance